Screw torque traceability control: industrial application

• Silva, Carlos Americo de Souza ^[1] ; Uhlmann, Iracyanne Retto ^[2] ; Frazzon, Enzo Morosini ^[2]
  1. [1] Instituto de Tecnologia Educação Galileo da Amazônia
  2. [2] Industrial and Systems Engineering Department, Technology Center, Federal University of Santa Catarina
• Localización: Independent Journal of Management & Production, ISSN-e 2236-269X, Vol. 11, Nº. 2, 2020 (Ejemplar dedicado a: Independent Journal of Management & Production), págs. 538-547
• Idioma: inglés
• DOI: 10.14807/ijmp.v11i2.1038
• Enlaces
  • Texto completo (pdf)
• Resumen

  • This paper analyses a new screw torque traceability control procedure designed for an operation in a car audio workstation. First the detection score at a Failure Mode and Effects Analysis (FMEA) indicated which process improvement were needed. On the sequence, data was collected to evaluate performance indicators. Finally, specific actions were executed based on the improvement plan. As result, the FMEA detection score improved from 7 to 3, the run rate increased from 12 to 16 products/h and defects caused by improper screwing were eliminated. This research contributes to disseminate a practical application of a screw torque traceability control.

• Referencias bibliográficas
  • BERGER, E.; GREHL, S.; VOGT, D.; JUNG, B.; AMOR, H. B. (2016) Experience-based torque estimation for an industrial robot. In Robotics and...
  • BISCHOFF, R.; KURTH, J.; SCHREIBER, G.; KOEPPE, R.; ALBU-SCHÄFFER, A.; BEYER, A.; HIRZINGER, G. (2010) The KUKA-DLR Lightweight Robot arm-a...
  • CHEN, C. H. (2014) Fastening torque control for robotic screw driver under uncertain environment. In Control, Automation and Systems (ICCAS),...
  • GANESHMURTHY, S.; NASSAR, S. A. (2014) Finite element simulation of process control for bolt tightening in joints with nonparallel contact....
  • HERMANSSON, T. O. (2016) Quality assured tightening of screw joints. Proceedings of the Institution of Mechanical Engineers, Part C: Journal...
  • LI, S.; HAN, M.; DENG, L. (2009) Research on CNC machining screw which is variable pitch & groove depth & groove width. In Computer-Aided...
  • LIU, H. C.; LIU, L.; LIU, N. (2013) Risk evaluation approaches in failure mode and effects analysis: A literature review. Expert systems with...
  • LIU, S.; GE, S. S.; QIN, G.; LI, M. (2015) An Automatic Screw Tightening Shaft Based on Enhanced Variable Gain PID Control. International...
  • MUELANER, J. E.; CAI, B.; MAROPOULOS, P. G. (2010) Large-volume metrology instrument selection and measurability analysis. Proceedings of...
  • OGAWA, S.; SHIMONO, T.; KAWAMURA, A.; NOZAKI, T. (2015) Position control in normal direction for the fast screw-tightening. In Industrial...
  • OGUSHI, K.; NISHINO, A.; MAEDA, K.; UEDA, K. (2015) Direct calibration chain for hand torque screwdrivers from the national torque standard....
  • PERSSON, E.; ROLOFF, A. (2016) Ultrasonic tightening control of a screw joint: A comparison of the clamp force accuracy from different tightening...
  • SAFARI, H.; FARAJI, Z.; MAJIDIAN, S. (2016) Identifying and evaluating enterprise architecture risks using FMEA and fuzzy VIKOR. Journal of...
  • SCHNEIDER, H. (1996) Failure mode and effect analysis: FMEA from theory to execution. Technometrics, v. 38, n. 1, p. 80.
  • TRIPP, D. (2005) Pesquisa-ação: uma introdução metodológica. Educação e pesquisa, v. 31, n. 3, p. 443-466.
  • WEN, K.; DU, F.; ZHANG, X. (2016) Algorithm and experiments of six-dimensional force/torque dynamic measurements based on a Stewart platform....
  • WOLF, C. M.; LORENZ, R. D. (2011) Using the motor drive as a sensor to extract spatially dependent information for motion control applications....